Products

DescriptionGeorge's Garage, 00-up sealed wheel bearing toolDetailsRemoves & installs all 1 inch and 25mm sealed wheel bearings00-21 B.T., 00-21...

DescriptionGeorge's Garage, 36mm rear wheel axle wrenchDetailsLoosen and tighten the 36mm OEM 8020 36mm (M24x2.0x15) rear wheel axle nut, for drive...

DescriptionGeorge's Garage, 5&6-sp transmission shaft install toolDetailsUsed to install transmission shafts without the use of a press80-21 5 ...

DescriptionGeorge's Garage, bearing re-greaserDetailsHand operated. For up to 3.7" (94mm) diameter bearings. Used to re-grease Timken style bearing...

DescriptionGeorge's Garage, cam & pinion gear gauge pins .105"Details.105 inch diameter. Used to check pinion and cam gears for pitch diameters...

DescriptionGeorge's Garage, cam bearing installer toolDetailsInstalls cam shaft bearing Note: 979461 driver handle required for installation and m...

DescriptionGeorge's Garage, cam bearing installer toolDetailsUsed to install the needle bearing from crankcase with a controlled press-in action; C...

DescriptionGeorge's Garage, cam bearing remover toolDetailsUsed to remove the needle bearing from crankcase with a controlled press-out action; Cas...

DescriptionGeorge's Garage, cam bearing remover toolDetailsUsed to pull camshaft roller bearings from camshaft once camshafts are removed from the ...

DescriptionGeorge's Garage, cam chain tensioner toolDetailsUsed to unload pressure from the cam chains when working on the cams.99-06 Twin Cam (exc...

DescriptionGeorge's Garage, cam relief pilotDetailsAdapts 979418 and / or 979419 (99-06) tool so it is compatible with (06-17) hydraulic chain tens...

DescriptionGeorge's Garage, cam relief toolDetailsDual spindle; Used to machine cases for high lift cams99-06 Twin Cam (excl. 2006 Dyna)

DescriptionGeorge's Garage, cam/crank gear locking toolDetailsUsed to lock camshaft gears & pinion gears for torquing to specs06-17 Dyna; 07-17...

DescriptionGeorge's Garage, cam/crank gear locking toolDetailsUsed to lock camshaft gears & pinion gears for torquing to specs99-06 Twin Cam (e...

DescriptionGeorge's Garage, camshaft assembly toolDetailsDelrin; Holds both camshafts in an upright position while lowering the cam support06-17 Dy...

DescriptionGeorge's Garage, camshaft remover & installer toolDetailsUsed to remove & install camshafts and the ball bearings99-06 Twin Cam ...

DescriptionGeorge's Garage, clutch spring adapter nutDetailsFor use with 979429 clutch spring compressor tool. Makes 979429 compatible with Sportst...

DescriptionGeorge's Garage, clutch spring compressorDetailsUsed to release clutch spring for removal and installation of retaining ring. Note: ...

DescriptionGeorge's Garage, crankshaft bearing toolDetailsUsed to remove & install left sprocket shaft & right side pinion shaft crankcase ...

DescriptionGeorge's Garage, cylinder torque platesDetailsFor 3.750 - 3.938 more cylinders with STD bolt pattern; Plates simulate stress conditions ...

DescriptionGeorge's Garage, cylinder torque platesDetailsStock to 4.00 - 4.060 inch bore cyl. with OEM bolt pattern; Plates simulate stress conditi...

DescriptionGeorge's Garage, driver handle 12"DetailsUsed with 979457 steering head bearing race tool and 979453 wheel bearing race tool

DescriptionGeorge's Garage, driver spacerDetailsUsed with 979457 steering head bearing race tool; Is used between tool so tool will keep a firm gri...

DescriptionGeorge's Garage, exhaust stud drill jigDetailsTool used to drill out broken exhaust studs.84-21 B.T.; 86-21 XL; 08-12XR1200; 87-10Buell XB

DescriptionGeorge's Garage, FLT power train alignment toolDetailsUsed to align engine, transmission and swingarm with each other to the correct pos...

DescriptionGeorge's Garage, fork seal & bushing install toolDetailsFor 41mm forks; Used to install fork seals & bushings in fork sliders; T...

DescriptionGeorge's Garage, fork seal & bushing install toolDetailsFor 39mm forks; Used to install fork seals & bushings in fork sliders; T...

DescriptionGeorge's Garage, fork seal & bushing install toolDetailsFor 49mm forks; Used to install fork seals & bushings in fork sliders; T...

DescriptionGeorge's Garage, fuel pump retainer remover toolDetailsUsed to remove and install the retaining ring that holds fuel pump and fuel filte...

DescriptionGeorge's Garage, ignition switch connector toolDetailsUsed to remove the electrical connector without damage to the ignition switch.03-2...

DescriptionGeorge's Garage, ignition switch housing toolDetailsUsed to correctly align ignition switch housing for installation.03-13 Touring; 02-1...

DescriptionGeorge's Garage, inner cam bearing installer toolDetailsUsed to install the inner cam bearings at .023" to .028" depth06-17 Dyna; 07-17 ...

DescriptionGeorge's Garage, inner cam bearing installer toolDetailsUsed to install the inner cam bearings Note: See 979480 update bearing pilot fo...

DescriptionGeorge's Garage, inner cam bearing remover toolDetailsUsed to pull inner cam bearings from the crankcase06-17 Dyna; 07-17 Softail; 07-16...

DescriptionGeorge's Garage, inner cam bearing remover toolDetailsUsed to remove the inner cam bearings99-06 TCA/B (EXCL. 2006 DYNA)

DescriptionGeorge's Garage, main drive gear & bearing toolDetailsUsed to remove & install the main drive gear and main drive gear case bear...