George's Garage

Description Used to install the needle bearing from crankcase with a controlled press-in action; Case disassembly is not required Note: See 979404 ...

Description Used to lock cam gears and pinion gears for removal and torquing to correct specs upon installation. Fitment 99-06 Twin Cam (Excl. 2006...

Description .108 inch diameter. Used to check pinion and cam gears for pitch diameters. A loose fit results in a clicking noise but a tight fit in ...

Description Removes and installs the wristpin in a controllable process with slide hammer action. No need to use force. Fitment 36-99 Big Twin (Exc...

Description Installs cam shaft needle bearing. Note: 979461 driver handle required for installation and must be purchased separately Fitment 58-99 ...

Description Used to correctly align ignition switch housing for installation. Fitment 03-13 Touring; 02-17 V-Rod (NU) Product Details Brand: Geor...

Description Used to remove and install the Timken sprocket shaft bearing race in the left side engine case; Note: To be used with 979461 driver han...

Description Hand operated. For up to 3.7" (94mm) diameter bearings. Used to re-grease Timken style bearings; quickly & efficiently. With dust c...

Description Removes & installs right side pinion shaft crankcase bearing without damage Fitment 99-02 Twin Cam A Dyna; Touring (Excl. Twin Cam ...

Description Allows 979411 cam installer tool to work on late model Twin Cams Fitment 06-17 Dyna; 07-17 Softail; 07-16 Touring (NU) Product Details ...

Description Used to remove and install the retaining ring that holds fuel pump and fuel filter. Prevents leakage. For quick and easy service of the...

Description Used to remove and install the nut holding the pinion gear. For use with 1/2" drive ratchet. Fitment 54-92 Big Twin (NU) Product Detail...

Description Used to install the inner cam bearings at .023" to .028" depth Fitment 06-17 Dyna; 07-17 Softail; 07-16 (NU) Touring Product Details ...

Description Used to install the inner cam bearings Note: See 979480 update bearing pilot for adapting 979411 tool to 06-17 Twin Cam Fitment 99-06 T...

Description Tool used to help drill out broken exhaust studs in the cylinder head. Drill bit included. Fitment 84-26 Big Twin; 86-22 (NU) XL Sports...

Description Adapts 979418 and / or 979419 (99-06) tool so it is compatible with (06-17) hydraulic chain tensioners Fitment 06-17 Dyna; 07-17 Softai...

Description Delrin; Holds both camshafts in an upright position while lowering the cam support Fitment 06-17 Dyna; 07-17 Softail; 07-16 Touring (NU...

Description Used to lock motor sprocket & clutch basket for removal and installation of the engine and clutch hub nuts. Fitment 06-17 (NU) Dyna...

Description Can be used with impact air wrenches. -7/8" hex with 1/2" drive. Removes & installs the 1-1/2"-24 hex nut (35211-36 and 35211-91B) ...

Description Used to press sprocket shaft seal into left crankcase; with sprocket shaft installed Fitment 70-17 Big Twin (Excl. M8) Product Details ...

Description Used to install transmission shafts without the use of a press Fitment 80-25 5 & 6-speed Big Twin Product Details Brand: George''...

Description Used to install 12074 / 12074A main drive gear seal. Includes pilot for seal protection. Can be used with transmission in frame. Fitmen...

Description Used to lock motor sprocket & clutch basket for removal and installation of the engine and clutch hub nuts. Fitment 80-06 5-speed F...

Description Used to remove transmission doors; with gears and shaft attached; without causing damage to door bearings. Note: Will not fit 2006-up O...