Engine

DescriptionPushrod Kit Super-light, heavy-duty fixed-length pushrods Sold in sets of four to replace OE; two shorter rods for intake, two longer ro...

DescriptionAdjustable Pushrod KitChromoly steel for maximum strengthRocker boxes must be removed for installationMade in the U.S.A.SpecificationsUn...

DescriptionCam Set for Chain Drive Broad tip cams for baggers with stock motors; max torque at low and mid rpm ranges Manufactured with the help of...

DescriptionCam Installation Kit Includes all gaskets, bearings and hardware necessary to install gear-driven cams Made in the U.S.A. Specifications...

DescriptionRoller Conversion Cam Sprocket 34 teeth with ignition trigger ring Must use with 99-01 engines with stock ignition 02-06 engines can use...

DescriptionN3 Grind Cams Cams run to 6500 rpm with stock hydraulic lifters; recommend solids not be installed Stock base circle sizes allow the use...

DescriptionValve Spring Upper Collars Similar to stock 80-style parts, but lower profile for easier installation of higher lift cams Required parts...

DescriptionMedium-Lift Upper Spring Collar Set Intended to work with stock springs and add approximately .060" spring travel with no other modifica...

DescriptionHigh-Lift Valve Springs Provide correct spring force for any of our performance cams when used in 74" and 80" motors Max lift; installat...

DescriptionLow-Profile Lower Spring Collars Similar to the late H-D collars Will provide .060" more spring travel than stock collars Made in the U....

DescriptionJ Grind Cam More mid-range and top-end power for street and drag bikes. These cams work with solid or hydraulic lifters, and the idle re...

DescriptionJ Grind Cam More mid-range and top-end power for street and drag bikes. These cams work with solid or hydraulic lifters, and the idle re...

DescriptionJ Grind Cam More mid-range and top-end power for street and drag bikes. These cams work with solid or hydraulic lifters, and the idle re...

DescriptionCam Set for Chain Drive Manufactured with the help of a computer with cam design capabilities Made from alloy steel billets and heat-tre...

DescriptionCam Set for Chain Drive Manufactured with the help of a computer with cam design capabilities Made from alloy steel billets and heat-tre...

DescriptionCam Set for Chain Drive Manufactured with the help of a computer with cam design capabilities Made from alloy steel billets and heat-tre...

DescriptionAdjustable Pushrods Andrews completely adjustable pushrods easily replace the nonadjustable stock pushrods on H-D engines Made in the U....

DescriptionReplacement Pushrod Kit Pushrods fit Shovel engines using stock diameter tubing so there is no cover tube interference For stock stroke ...

Description554 Cam For 124" and 128" big-bore motors with head work Made in the U.S.A. Requires Hi-lift springs. SpecificationsGrind : 554 SeriesCo...

Description57 Series Grind Cam Bolt-in broad tip cams; 96" , 103" Limited and 110" CVO engines Cams work best at rpm range of 2200-5600 Specificati...

DescriptionCam Set for Chain Drive Broad tip cams for baggers with stock motors; max torque at low and mid rpm ranges Manufactured with the help of...

DescriptionCamshaftWith four valve heads and 106 cubic inches more power is readily availableEU: With four valve heads and 1,74 L, more power is re...

DescriptionM464 CamGreat mid-range torque and power with free-flow exhaust pipes and injector tuningSpecificationsExhaust Lobe Centerline Imperial ...

DescriptionM462 Cam Bolt-in cam 107”-114” engines Big power; 127 ft lb and 109 hp (from 1200 to 5500 rpm) SpecificationsExhaust Lift Imperial : 0.4...