Tools

DescriptionT-6 Combo Lever Adaptor3/8" drive male and 1/4" drive female for use with sockets for smaller front axles3/8" square drive is rated for ...

DescriptionT6 Tyre LeverHex end is rated for a maximum torque of 90 ft/lbPerfectly contoured tyre spoon on one endLightweight forged 7075-T6 alumin...

DescriptionT6 Tyre LeverHex end is rated for a maximum torque of 90 ft/lbPerfectly contoured tyre spoon on one endLightweight forged 7075-T6 alumin...

DescriptionT6 Tyre LeverHex end is rated for a maximum torque of 90 ft/lbPerfectly contoured tyre spoon on one endLightweight forged 7075-T6 alumin...

DescriptionT6 Combo LeverUnique no-pinch lip on tyre spoon is designed to avoid tube pinch when installing tyresHex end is rated for a maximum torq...

DescriptionBrake Caliper Piston ToolUltra-low-profile design removes pistons from monoblock disc brake calipersFits pistons with a centre bore size...

DescriptionRotor and Sprocket HolderHolds sprockets and rotors with holes centre-to-centre at a minimum distance of 1/2" (13 mm) and a maximum dist...

DescriptionMaster Cylinder Snap-Ring PliersCan be used to remove and replace small to medium internal snap rings up to 50 mm deep, including those ...

DescriptionChain Master Link Press ToolWorks on all 50 series chains and has a maximum master link width of 24.8 mmPresses on side plates with roll...

DescriptionSprocket Jammer™Prevents rotation of chain and sprockets for easy removal or installation of countershaft nutCan be used to pull rear wh...

DescriptionFolding Sag Scale IICone-shaped axle locating pin fits hollow axles up to 20 mm with repeatable precisionAdjustable zero-set point for d...

DescriptionPBR Chain ToolIndexing letters on movable anvil and body ensures correct tool configuration; simply line up the letter on the anvil to t...

DescriptionChain Breaker, Press and Riveting ToolComplete chain tool for most 520, 525 and 530 standard, O-ring and X-ring chainsHardened body, riv...

DescriptionSteering Head Race PullerDesigned to quickly and precisely remove outer bearing race from the steering head without the use of a hammer ...

DescriptionReplacement Pins for Heavy-Duty Pin SpannerPins are heat treated steel for strength and durabilityReplacement pins for the heavy-duty pi...

DescriptionHeavy-Duty Pin SpannerDesigned for removal and installation of shock reservoirs, screw-in seal heads, fork caps, and bearing retainersBi...

DescriptionFork Cap SocketFits '14 KTM XC models and all '13-'14 Husaberg with WP 4860 4CS forkFor removing and installing left hand and right hand...

DescriptionWP Shock Clevis Jam Nut SocketDesigned for removal of oval-profile clevis jam nut common on WP shock absorbersOpen-end design allows for...

DescriptionShock Bearing PullerReversible puller cup with cutaway fits a wide variety of shock reservoir and compression adjuster configurationsSaf...

DescriptionFork Seal Bullet SetProtects the fork seal and wiper of inverted forks from damage by the bushing groove during installationFitment size...

DescriptionRinger® Fork Seal DriverLocking ring features knurled finish for secure no-slip grip and positively locks body halves together during us...

DescriptionRinger® Fork Seal DriverLocking ring features knurled finish for secure no-slip grip and positively locks body halves together during us...

DescriptionPivot Suspension ViceRepositionable bottom slide bar holds forks compressed while bleeding air (priming cartridge) during reassembly and...

DescriptionSealmate Fork Seal CleanerExtracts dirt and debris trapped between fork seal and tubeEasy way to keep fork seals clean and debris freeWo...