jim's

DescriptionJIMS, 'TALLER' ENGINE STANDDetailsSteel stand with a tough powder coated finish.1 1/2" taller for better access. Includes notch for cran...

DescriptionJIMS, +.010" o.s. hydraulic Powerglide tappetDetailsPowerglide II tappet designed for use with 961550 +.010" o.s. tappet bore reamer too...

DescriptionJIMS, +.010" tappet bore reamer toolDetailsUsed to ream worn or damaged tappet bores to +.010" oversize (.8536") when tappet bores are d...

DescriptionJIMS, 00-UP SEALED WHEEL BEARING TOOLDetailsRemove & install all 3/4" (19.05mm), 1" (25.4mm) and 25mm ID wheel bearings; Note: Use...

DescriptionJIMS, 10 degree lash cap recess valve keysDetailsWith lash cap recess. A lash cap recess allows the installation of a steel lash cap on ...

DescriptionJIMS, 10 degree lash cap recess valve keysDetailsWith lash cap recess. A lash cap recess allows the installation of a steel lash cap on ...

DescriptionJIMS, 1361G cam .500" lift for Evo Big TwinDetails.500" valve lift. For 80" engines with stock heads. Bolt-in cam with a broad useable t...

DescriptionJIMS, 15-73 tappet adjusting screw kitDetails9/32-32 threaded. Fits as stock replacement and all other tappets that are 9/32-32 threaded...

DescriptionJIMS, 24-73 Flathead crankpinDetailsStandard O.D. 1.000". 1-hole oiling design for stock flywheels. Use JIMS 978260 crankpin nuts. Use J...

DescriptionJIMS, 29-85 tappet roller repair kitDetailsComplete reproduction tappet rollers with needle bearings and axles. Repl. 18534-29A. Tec...

DescriptionJIMS, 35mm fork tube nut socketDetailsInstalls & removes the top fork tube cap; 3/8" drive; Rubber protector inside; Clears most han...

DescriptionJIMS, 36-52 chromoly tappet adjusting screw kitDetails4340 chromoly steel. With 3/8" ball end and 9/32"-32 threaded. OEM style reproduct...

DescriptionJIMS, 36-52 crankpin. STDDetailsStandard O.D. 1.249". 1-hole design for stock flywheels. Use JIMS 978250 crankpin nuts and 978618 woodru...

DescriptionJIMS, 3rd. hand axle locker toolDetailsInstalls on welded nut of rear axle; Prevents axle from turning when torquing down axle which pre...

DescriptionJIMS, 4 & 5 speed mainshaft seal toolDetailsUsed to install and remove transmission mainshaft seal; Fits 36-76 4-sp B.T.; Will fit l...

DescriptionJIMS, 4 & 5-speed transmission stand (vice type)DetailsUsed to clamp the transmission in a vice; Note: Not compatible with models ...

DescriptionJIMS, 4-sp mainshaft starter clutch gear pullerDetailsUsed to pull the starter clutch gear, on models with kickstart. Tool will not slip...

DescriptionJIMS, 41-E81 crankpin kit. STDDetailsIncl. nuts & keys. Standard O.D. 1.2490". 3-hole oil design. This convienient precision kit inc...

DescriptionJIMS, 41-E81 crankpin. STD but 0.25" shorterDetailsThis special crankpin is identical to the JIMS 506870 crankpin but are ground shorter...

DescriptionJIMS, 41-E84 crankpin, 180 degree. STDDetailsStandard O.D. 1.2490". 3-hole oil design on 180° for improved lubrication of the bearing di...

DescriptionJIMS, 41-E84 crankpin. STDDetailsStandard O.D. 1.2490". 3-hole oil design. Use Jims 978251 crankpin nuts. Use Jims 978618 (Repl. 23985-1...

DescriptionJIMS, 41mm fork nut socketDetailsRemoves & installs fork tube plugs (that are screwed inside fork tube). Eliminates possible burring...

DescriptionJIMS, 4340 chromoly steel tappet screws. SpecialDetails4340 chromoly steel. Screw has oil hole drilled through the center for running a ...

DescriptionJIMS, 48-84 solid adjustable tappet. Standard .731" O.DDetailsNon-hydraulic tappet. Weight 86 grams each. Must be used with 53-84 B.T. h...