Products

DescriptionJIMS, engine & transmission plug kitDetailsUsed instead of rags. Provides enough plugs to fully seal all Twin Cam and transmission h...

DescriptionJIMS, engine cradle for 36-99 B.T.DetailsBlue; Steel; Used with 978395 base stand; For 36-99 single cam H-D engines36-99 B.T. (excl. Twi...

DescriptionJIMS, engine cradle for SportsterDetailsBlue; Steel; Use with 978395 base stand; Will not take 04-up rubber mounted engines57-03 Sportst...

DescriptionJIMS, engine cradle for Twin Cam ADetailsuse with 978395 base stand99-17 Dyna; 99-16 FLT/Touring

DescriptionJIMS, engine cradle for Twin Cam BDetailsBlue; Steel; Use with 978395 base stand00-17 TCB Softail

DescriptionJIMS, ENGINE ROTATOR TOOLDetailsUsed to rotate the assembled engine, fits to sprocket shaft, when doing pushrods or engine timing; With ...

DescriptionJIMS, engine standDetailsSteel stand with a tough powder coated finish. Takes the Twin Cam A engine (engine without balancers).99-17 Dyn...

DescriptionJIMS, engine stand Sportster/BuellDetailsSteel stand with a tough powder coated finish.57-03 Sportster; 94-02 Buell (excl. XB models)

DescriptionJIMS, engine stand Twin Cam BDetailsSteel stand with a tough powder coated finish.00-17 Softail

DescriptionJIMS, Evo Big Twin crankcase boring toolDetailsUsed to bore Evo Big Twin cases with stock cyl. stud pattern up to 3.8125" spigot diamete...

DescriptionJIMS, Evo B.T. Pro-Lite Worksavers aluminum pushrod setDetailsQuick installs without removing rocker covers. Manufactured from blue anod...

DescriptionJIMS, Evo compression release valve toolDetailsDrill fixture tool. Used to machine Twin Cam heads so heads will accept the JIMS mechanic...

DescriptionJIMS, exhaust gasket installer toolDetailsBlue anodized aluminum. Used to install exhaust gaskets straight and without distortion.84-21 ...

DescriptionJIMS, exhaust pipe retaining ring install toolDetailsNo more wrestling exhaust pipe retaining rings. This tool is designed to install th...

DescriptionJIMS, exhaust stud drill plateDetailsTool used to completely drill out a broken exhaust stud. Compatible with all Evo, Twin Cam and M8 m...

DescriptionJIMS, EXTERNAL LOCK RING PLIERSDetailsUsed to install & remove snap rings (retaining rings) MCS 500975 / OEM 11067. Jaws are scored ...

DescriptionJIMS, Extra Grip tool driver spacerDetailsOptional for use with all JIMS 2-piece bearing race tools; Applies outwards force for better t...

DescriptionJIMS, FAT-5 TRANSM. SUPERKITDetailsINCL. GEARCLUSTER INSTALLED IN TRAPDOOR90-00 FXST, FXD, FXR

DescriptionJIMS, FAT-5 TRANSMISSION, BLACKDetailsX-TRA WIDE GEARS & +.560" WIDER SIDE COVER90-99 FXST (OVERDRIVE)

DescriptionJIMS, FEED GEAR, DRIVEN. OIL PUMPDetails68-99 B.T. (EXCL. TC)

DescriptionJIMS, FLT oil filler spout spacerDetailsAluminum; 1-7/8 inch thick93-06 FLT/Touring with OEM 5-speed or aftermarket 6-speed transmission

DescriptionJIMS, FLT/Touring rear wheel axle toolDetailsLoosen and tighten the 36mm OEM 8020 36mm (M24 x 2.0 x 15) rear wheel axle nut, for drive b...

DescriptionJIMS, flywheel holder toolDetailsUsed to hold flywheels in vice, with or without left case attached06-17 Dyna; 07-17 Softail; 07-16 Tour...

DescriptionJIMS, flywheel holder toolDetailsUsed to hold flywheels in vice, with or without left case attached55-06 B.T. (excl. 2006 Dyna)

DescriptionJIMS, flywheel run-out inspection gaugeDetailsUsed to check flywheel run-out (trueness) from the pinionshaft while assembled in the cran...

DescriptionJIMS, flywheel socket 1-1/4 x 1/2 driveDetailsInstalls and removes 24016-80 pinion shaft nut. Used when rebuilding flywheel assemblies. ...

DescriptionJIMS, flywheel socket 1-5/16 x 1/2 driveDetailsInstalls and removes 23966-54A crank pin nut. Used when rebuilding flywheel assemblies. M...

DescriptionJIMS, flywheel truing toolDetailsUsed to fine-tune flywheel assemblies when truing. This tool features a flywheel expander and a compres...

DescriptionJIMS, fork cap allen socketDetailsUsed to install & remove the large OEM 45500117 allenhead fork tube cap on late model Tourings wit...

DescriptionJIMS, fork cap installation toolDetailsUsed to overcome spring pressure when installing the fork tube caps. Makes installing much easier...

DescriptionJIMS, fork stem bearing puller toolDetailsRemoves all conical (tapered) bearings (OEM 48300-60 and other Timken style) from the lower tr...

DescriptionJIMS, fork tube holder toolDetailsBlue anodized aluminum. Used to hold fork tubes, with or without sliders attached, for hands-free serv...

DescriptionJIMS, fork tube seal install slider & cap toolDetailsFor 39mm fork tubes; Includes installer cap; Used to install fork seals, dust s...

DescriptionJIMS, fork tube spring retainer toolDetailsUsed to remove and install the fork tube retainer screw on the early drum brakes71-72 FX; 52-...

DescriptionJIMS, fuel pump retainer remover toolDetailsUsed to remove and install the retaining ring that holds fuel pump and fuel filter. Prevents...

DescriptionJIMS, fuel tank wall mountDetailsUsed to provide a storage space in the workshop for fuel tanks of bikes that are being serviced. Tempor...