Products

DescriptionJIMS, main drive gear seal installerDetailsIncl. 576558 driver handle; Installs seal MCS 908250 / OEM 12013A and MCS 519891 / OEM 12035B...

DescriptionJIMS, maindrive gear bearing & seal install toolDetailsUsed to install main drive gear bearings and seal; Tool will hold bearings an...

DescriptionJIMS, maindrive gear/cam bushing toolDetailsRemoves & installs main drive gear bushing; Installs cam bushing36-86 4-sp B.T (main dri...

DescriptionJIMS, MAINSHAFT 4-SPDetails70-E84 4-SP B.T.

DescriptionJIMS, MAINSHAFT BEARING RACE TOOLDetailsUsed to remove and install the inner bearing race 34091-85A (MCS 999185), 34091-06 (MCS 921493) ...

DescriptionJIMS, mainshaft oil seal installerDetailsUsed to install the large OEM 12074 mainshaft oil seal straight and to correct depth, without d...

DescriptionJIMS, MECHANIC'S STETHOSCOPEDetailsWith metal probe to find the origin of engine noise

DescriptionJIMS, mini valve spring testerDetailsTests up to 0-600 PSI spring pressure. Can be used in a vice, arbor or drill press.UNIV.

DescriptionJIMS, Mityvac hand vacuum pump kitDetailsUsed with JIMS 978613 vacuum fork filler tool

DescriptionJIMS, modular base stand for engine cradlesDetailsThis JIMS modular engine base stand makes manipulating heavy engines into the right po...

DescriptionJIMS, MOTOR SPROCKET NUT. OEM TYPEDetailsWITHOUT COMPENSATING SPROCKET; 7/8-14 THREAD55-E70 FL

DescriptionJIMS, multifunctional clutch hub puller toolDetailsMulti-purpose tool. Used to pull, amongst others, clutch hubs. This puller is numbere...

DescriptionJIMS, needle bearing camshaft. 'Full needle'DetailsWhen still present it is advised to replace the low cost OEM needle bearing in 92-99 ...

DescriptionJIMS, Needle Sharp multimeter probe kitDetails17-piece kit. Used for precise and non damaging diagnostic work. Pins can be used with sta...

DescriptionJIMS, neutral switch transmissionDetailsStock style replacement transmission neutral switch.59-64 FL; L73-E79 B.T.; 80-975-sp B.T.; 86-9...

DescriptionJIMS, nut pinion shaftDetails3/4-20 threaded. On flywheel side. Repl. 24016-80.L81-88 B.T.

DescriptionJIMS, nut. Pinion shaft gearDetails5/8-24. Left hand threaded. Repl. 24023-54. Note: Use 513750 JIMS tool for removing & install...

DescriptionJIMS, nut. Pinion shaft gearDetails5/8-24. Left hand threaded. Repl. 24022-90. Note: Use 513750 JIMS tool for removing & install...

DescriptionJIMS, oil filter cutter toolDetailsMakes a clean cut on oil filter base for content inspection; Works with all spin-on oil filters up to...

DescriptionJIMS, oil filter cutting standDetailsFor use with 961456 oil filter cutter; Grips oil filter for non-slip cutting actions; Tool mounts i...

DescriptionJIMS, oil filter wrenchDetailsInstalls & removes regular spin on oil filters with 76mm diameter and 14 flats; 3/8" driveALL B.T., BUELL

DescriptionJIMS, OIL METERING SCREW. PINION SHAFTDetailsUsed to control oil flow to connecting rod rollers. Hole size .087". Replacement for JIMS p...

DescriptionJIMS, oil pump & tappet block alignment screwDetailsUsed to align oil pump to the cam support plate. Helps reduce oil pump scavengin...

DescriptionJIMS, OIL PUMP DRIVE SHAFTDetails70-99 B.T. (EXCL. TC)

DescriptionJIMS, OIL PUMP SEAL INSTALLER TOOLDetailsUsed to install the oil pump seal into the oil pump housing, perfectly below gear surface, with...

DescriptionJIMS, OIL PUMP SNAP RING INSTALLERDetailsUsed to install outer retaining ring on the oil pump drive shaft36-99 B.T. (excl. Twin Cam)

DescriptionJIMS, onboard diagnostic volt meterDetailsSmall volt meter; 12/6 volt compatible; digital display; Includes wiring with replaceable fuse...

DescriptionJIMS, outer balancer bearing toolDetailsUsed to Install & remove the outboard balancer bearing on chain guide support plate07-17 Sof...

DescriptionJIMS, outer bearing remover / installer onlyDetailsReplacement part for 961430 outer balancer bearing tool07-17 Softail

DescriptionJIMS, camshaft bushing, outer. STDDetailsOuter diameter .9405". Used in the cam cover. Tech tip: Cam cover bushings are counted from r...

DescriptionJIMS, outer primary starter bearing pullerDetailsUsed to remove 509395 / OEM 9063 bearing in outer primary cover65-88 B.T.; 67-80 XL

DescriptionJIMS, Panhead 'Slim JIMS' aluminum pushrod setDetailsFor models with OEM style hydraulic units only for use with stock hydraulic or equi...

DescriptionJIMS, pin extractor toolDetailsEasily removes Molex style pin from connector housing. Note: See 978458 for Molex style receptable extr...

DescriptionJIMS, pinion / idler bushing gear line reamer toolDetailsUsed to line ream the pinion shaft bushing in the cam cover; Also reams idler g...

DescriptionJIMS, pinion bushing installer/drill jigDetailsUse with MCS 978010 / OEM 25582-36 bushing and MCS 519008 / OEM 275 dowel pin36-53 B.T.

DescriptionJIMS, PINION BUSHING PULLER TOOLDetailsUsed to pull pinion shaft bushing from the cam cover. Note: A handy helping hand is the JIMS ...